Skip to content

Furnace Repair in Los Altos, CA

Serving Los Altos and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (669) 274-2169

The short answer

ArcticFlow AC Repair diagnoses and repairs gas furnaces in Los Altos, CA, including no-heat calls, ignition failures, short cycling, and blower problems. Air District rules don't require you to replace a working furnace, so repairing a sound unit is often a reasonable choice. If replacement makes more sense, we'll explain your options, including heat pumps.

When your furnace quits on a cold, damp Los Altos evening, you need to know what failed and what it will take to fix it. ArcticFlow AC Repair sends technicians from our Santa Clara base, about 6 miles east, to homes throughout Los Altos and the 94024 ZIP code. We diagnose gas furnaces, find the actual fault instead of guessing, and explain your options in plain terms. If a repair makes sense, we do it. If it doesn't, we'll say so, and we'll explain how current Bay Area Air District rules affect your next step.

Why Los Altos Furnaces Fail the Way They Do

The Santa Clara Valley has dry summers and mild, damp winters. Many Los Altos furnaces sit unused for months and then get switched on the first chilly night of fall. Over that idle stretch, dust settles on burners and flame sensors, filters stay in place longer than they should, and small problems go unnoticed until the heat is actually needed.

Mild winters bring a less obvious kind of wear. On cool but not cold days, a furnace runs in short bursts and starts and stops many times. Each start puts stress on the igniter, the inducer motor, and the control board. That's why many of the repairs we see here involve ignition and startup parts rather than the heat exchanger or the main blower.

Furnace Problems We Repair

Whether your furnace sits in a garage, attic, hall closet, or crawlspace, we troubleshoot the whole system, including the thermostat, wiring, and ductwork connections.

  • No heat, or the blower runs but the air stays cool
  • Furnace tries to light, then shuts off after a few seconds
  • Short cycling, where the furnace turns on and off too often
  • Failed hot surface igniters and dirty or worn flame sensors
  • Inducer motor noise, pressure switch faults, and blocked condensate lines on high-efficiency units
  • Blower motor and capacitor failures
  • Control board faults and error codes
  • Thermostat communication problems and wiring faults
  • Burning smells, rattles, squeals, or booming at startup

What Happens During a Repair Visit

We start by asking what you've noticed: when the problem began, what the furnace does, and any sounds or smells. Next we read the control board's fault codes, check the filter and airflow, and watch a full heating cycle. We test the ignition sequence, safety switches, gas pressure, and electrical parts until we find the cause.

Before any work begins, we tell you what we found, what the repair involves, and whether anything else looks close to failing. You decide how to proceed. Once the repair is done, we run the furnace through several cycles to confirm it lights, heats, and shuts off properly.

Repair or Replace? What Air District Rules Mean for You

Bay Area Air District appliance rules don't make you replace a furnace that works. They apply only when an existing furnace fails or is replaced. If your furnace is in sound condition and the problem is a fixable part, repair is often the sensible choice.

The rules do affect long-term planning. Under Rule 9-4, natural gas furnaces manufactured from 2029 on must meet a zero-NOx emission standard. In practice, that steers homeowners toward heat pumps when they replace a furnace after that date. If your furnace is aging and needs a major repair, we can walk you through the tradeoffs of repairing it now versus moving to a heat pump.

The federal 25C tax credit for heat pumps applied only to systems placed in service before December 31, 2025, so it isn't available for new installations. Bay Area homeowners can still check BayREN and their local clean energy provider for heat pump incentives. Amounts change with each funding cycle, so we confirm the current offer before including it in any quote.

Before You Call: Safe Checks to Try

A few simple checks can sometimes restore heat or help us diagnose the problem faster. Never open sealed burner compartments or work on gas components yourself.

  • Make sure the thermostat is set to Heat and the setpoint is above room temperature
  • Replace the batteries if your thermostat uses them
  • Check that the furnace power switch is on and the breaker hasn't tripped
  • Replace a filter that looks dirty or clogged
  • Make sure the furnace access panel is fully closed, since an open panel can keep the unit from starting
  • If you smell gas, leave the house right away and call your gas utility or 911 from outside
  • If a carbon monoxide alarm goes off, get everyone outside and call emergency services

More services in Los Altos

Related

What to expect

How a visit goes

  1. We find the cause first

    Before we replace a part or suggest new equipment, we test the system and pin down what's actually wrong. You get an explanation of the problem, not just a fix.

  2. We lay out your options

    When there's more than one reasonable path, such as repairing an older furnace versus moving to a heat pump, we explain the trade-offs so you can decide what fits your home and plans.

  3. We check incentives before quoting them

    Heat pump and electrification incentives through BayREN and local clean energy providers change from one funding cycle to the next. We confirm what's currently offered before we mention it in a quote.

FAQ

Common questions

Don’t see your question? Call (669) 274-2169 and we’ll talk it through.

Do you provide furnace repair throughout Los Altos?

Yes. We serve homes throughout Los Altos in the 94024 ZIP code from our base in Santa Clara, about 6 miles away. We also serve Los Altos Hills, Mountain View, Palo Alto, Sunnyvale, and Cupertino.

Will I have to replace my gas furnace because of Air District rules?

No. Bay Area Air District rules don't require you to replace working equipment. They apply only when a furnace fails or is replaced. Starting with units manufactured in 2029, new gas furnaces must meet a zero-NOx standard, which in practice points homeowners toward heat pumps.

Why does my furnace try to start and then shut off?

This is usually caused by a dirty or failing flame sensor, a weak igniter, a pressure switch fault, or restricted airflow. The control board shuts the furnace down as a safety measure when it can't confirm a steady flame or proper venting. We test each of these parts to find the actual cause.

Is it worth repairing an older furnace?

It depends on the furnace's overall condition, what failed, and your plans for the home. A worn igniter or sensor on a solid furnace is usually worth fixing. A cracked heat exchanger or a string of major failures may make replacement the better choice. We'll explain what we find so you can decide.

Can I still get a federal tax credit for a heat pump?

Not for new installations. The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025. Check BayREN and your local clean energy provider for current incentives. We confirm what's available before including it in a quote.

How often should I change my furnace filter?

Check it at the start of the heating season and every month or two while the furnace is in use. Replace it whenever it looks dirty. A clogged filter restricts airflow and can cause overheating and short cycling.

Tell us what your system is doing

Describe the problem, whether it's warm air from the vents, a furnace that won't start or a strange noise, and we'll schedule a technician to diagnose it and explain your options.

Call (669) 274-2169 Request Service