Skip to content

Furnace Repair in Santa Clara and Nearby Cities

Serving Santa Clara and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (669) 274-2169

The short answer

Call for furnace repair if your system blows cool air, short cycles, makes new noises, or won't respond to the thermostat. Most furnace problems are repairable, and Bay Area Air District rules don't require you to replace a furnace that still works. We diagnose the cause, explain your options and the price, and do the work only after you approve it.

Most Santa Clara Valley winters are mild and damp rather than freezing, so a furnace can sit idle for months and then run every evening once the weather turns. That stop-and-start pattern is often when problems show up: a burner that won't light, a blower that pushes cool air, or a system that shuts off after a few minutes. ArcticFlow AC Repair diagnoses and repairs gas furnaces for homeowners in Santa Clara, San Jose, Sunnyvale, Cupertino, and nearby cities. This page covers the warning signs to watch for, what we inspect, how we help you decide between repair and replacement, and what to expect during a visit.

Signs Your Furnace Needs Repair

Furnaces usually give some warning before they stop working entirely. Some signs are minor annoyances. Others point to safety problems that should not wait.

If you smell gas, leave the house and call your gas utility or 911 from outside before you call us. If a carbon monoxide alarm goes off, get everyone outside and call emergency services. Once the home is safe, we can find out what caused it.

  • No heat, or the blower runs but the air from the vents stays cool
  • The furnace starts and shuts off again within a few minutes (short cycling)
  • Some rooms stay noticeably colder than others when they didn't before
  • New noises, such as booming at startup, squealing, scraping, or rattling
  • A burning smell that continues well past the first few minutes of the season's first run
  • A yellow or flickering burner flame instead of a steady blue one
  • The thermostat calls for heat and nothing happens, or the furnace won't shut off
  • Soot around the furnace, unusual condensation on windows, or a carbon monoxide alarm going off

What We Check During a Furnace Repair Visit

A repair visit starts with a diagnosis. We don't replace parts until we know why the furnace is acting up, because the obvious symptom often comes from a problem somewhere else in the system.

We also look at the ductwork we can reach. Disconnected or crushed ducts in an attic or crawlspace can make a working furnace seem weak.

  • Thermostat settings, wiring, and power to the furnace
  • Error codes from the control board's diagnostic light
  • Igniter and flame sensor condition (a dirty flame sensor commonly causes a furnace to light and then shut off)
  • Gas pressure, burners, and flame quality
  • Inducer motor, pressure switch, and venting for blockages or disconnected sections
  • Heat exchanger, checked for visible cracks or corrosion
  • Blower motor, capacitor, and blower wheel
  • Air filter and return airflow, since a clogged filter can cause overheating and safety shutoffs
  • Limit switches and other safety controls
  • Condensate drain and trap on high-efficiency furnaces

Repair or Replace: How to Decide

Most furnace problems are repairable. Igniters, flame sensors, capacitors, pressure switches, and control boards are routine parts, and replacing a failed one can put a furnace back in normal service. We'll tell you what failed and why.

Replacement is worth discussing when the heat exchanger is cracked, when a major component fails on an older unit, when repairs keep adding up season after season, or when the system has never kept the house comfortable. A cracked heat exchanger is a safety concern. We'll explain what we found and show you when we can.

Local rules are part of the picture. Under the Bay Area Air District's appliance rules, natural gas furnaces manufactured starting in 2029 must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when a furnace is replaced after that date. The rules do not require you to replace a furnace that still works. They apply only when equipment fails or is replaced, so repairing a sound furnace is a reasonable choice that gives you time to plan.

If you're considering a heat pump, the federal Energy Efficient Home Improvement Credit covered only qualifying heat pumps placed in service before December 31, 2025, so it isn't available for new installations. Bay Area homeowners can still check BayREN and their local clean energy provider for heat pump and electrification incentives. Those programs change by funding cycle, so we confirm the current offer before including it in a quote.

What Affects the Cost of Furnace Repair

Before any repair work starts, we explain what it involves and what it will cost. The price depends on what we find. The main factors are:

Changing filters on schedule and keeping up with regular maintenance help keep repairs smaller and less frequent.

  • Which part failed, and whether it's a common part or specific to your furnace's make and model
  • Parts availability, especially for older or less common furnaces
  • Where the furnace is installed, since a garage closet is quicker to work in than a tight attic or crawlspace
  • Whether the problem is one failed part or several related issues
  • Venting or ductwork corrections needed for the furnace to run safely
  • Timing, such as a visit outside normal hours

How a Furnace Repair Visit Works

When you contact us, we'll ask what the furnace is doing, whether you've noticed error codes or noises, and roughly how old the system is. This helps the technician arrive with the parts most likely to be needed.

On site, the technician talks with you first, then tests the system from the thermostat through the furnace and venting. You get a plain explanation of the problem and your options before any work begins. If you approve the repair, we complete it, run the furnace through full heating cycles, and confirm it lights, heats, and shuts off as it should.

Before we leave, we'll point out anything worth watching, such as a filter due for replacement or wear on a part that still works for now. If you also have central air, mention any cooling concerns. Inland and southern parts of the valley run noticeably hotter in summer, and it's easier to deal with an AC problem before the heat arrives.

Furnace Repair by city

What to expect

How a visit goes

  1. We find the cause first

    Before we replace a part or suggest new equipment, we test the system and pin down what's actually wrong. You get an explanation of the problem, not just a fix.

  2. We lay out your options

    When there's more than one reasonable path, such as repairing an older furnace versus moving to a heat pump, we explain the trade-offs so you can decide what fits your home and plans.

  3. We check incentives before quoting them

    Heat pump and electrification incentives through BayREN and local clean energy providers change from one funding cycle to the next. We confirm what's currently offered before we mention it in a quote.

FAQ

Common questions

Don’t see your question? Call (669) 274-2169 and we’ll talk it through.

Why does my furnace turn on and then shut off after a few minutes?

Short cycling has several common causes, including a dirty flame sensor, a clogged air filter that makes the furnace overheat, a venting or pressure switch problem, or a thermostat issue. Start by checking the filter. If that doesn't fix it, a technician can test the components to find the cause.

Do Bay Area rules require me to replace my gas furnace?

No. The Bay Area Air District appliance rules don't require replacing working equipment. They apply only when a furnace fails or is replaced. Gas furnaces manufactured starting in 2029 must meet a zero-NOx standard, which points toward heat pumps for replacements after that date.

Is it safe to keep running a furnace that's making noise?

It depends on the noise. A light squeal may be a worn blower part, while booming at startup can mean delayed ignition. If you smell gas or a carbon monoxide alarm sounds, leave the house and call your gas utility or 911. Otherwise, turn the furnace off and schedule an inspection if you're unsure.

Can I still get a federal tax credit for a heat pump?

No. The federal Energy Efficient Home Improvement Credit covered qualifying heat pumps placed in service before December 31, 2025, and isn't available for new installations. Check BayREN and your local clean energy provider for current incentives. We confirm the current offer before quoting it.

Will you tell me the cost before doing the repair?

Yes. The technician diagnoses the problem, explains what needs to be done and your options, and gives you the price before starting. The repair begins only after you approve it.

What can I check before calling for furnace repair?

Make sure the thermostat is set to heat and set above room temperature, check that its batteries aren't dead, confirm the furnace's power switch and breaker are on, and replace a dirty air filter. If the furnace still doesn't work, schedule a repair visit.

Tell us what your system is doing

Describe the problem, whether it's warm air from the vents, a furnace that won't start or a strange noise, and we'll schedule a technician to diagnose it and explain your options.

Call (669) 274-2169 Request Service