Skip to content

Furnace Repair in Mountain View, CA

Serving Mountain View and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (669) 274-2169

The short answer

ArcticFlow AC Repair fixes furnaces in Mountain View homes in 94040, 94041 and 94043, including no-heat problems, short cycling, cold air from the vents and noisy blowers. Bay Area Air District rules don't require you to replace a working gas furnace. They apply only when a furnace fails or is replaced, and they set a zero-NOx standard for furnaces made from 2029 onward.

Mountain View sits closer to the Bay than much of the Santa Clara Valley, so winters here are mild and damp rather than harsh. Many furnaces run in short bursts on chilly mornings and evenings, sit idle for months, and then have to work again when the first cold snap arrives in late fall. That pattern is often when problems show up. ArcticFlow AC Repair sends technicians from our base in Santa Clara, about 6 miles southeast, to homes across 94040, 94041 and 94043. We find out why a furnace won't start, keeps shutting off, blows cold air, or has started making new noises, and we fix it.

Furnace problems we see in Mountain View homes

Heating season here is short and mild, so a lot of furnace trouble comes from equipment that sat unused for most of the year. Dust settles on the burners and flame sensor, filters get forgotten, and parts that were already wearing out fail on the first cold night. Damp winter air can also speed up corrosion on older components.

Signs that your furnace needs attention include:

  • The furnace won't turn on, or the blower runs but no heat comes out
  • Burners light, then shut off after a few seconds
  • Short cycling, where the furnace starts and stops over and over
  • Lukewarm or cold air from the vents
  • A burning-dust smell that lasts well past the first few minutes of the season
  • Rattling, squealing or banging from the blower or burners
  • A blinking light or error code on the control board
  • Some rooms stay warm while others stay cold

What happens during a furnace repair visit

The technician starts by asking what you've noticed and when it began. Next they check the thermostat, filter, power and gas supply before opening the furnace. Then they test the ignition system, flame sensor, safety switches, inducer and blower motors, and control board, and they read any fault codes.

We also inspect the venting and the heat exchanger for cracks, corrosion or signs of poor combustion, because those affect your safety as well as your comfort. Once we find the cause, we explain it in plain terms and describe the repair before any work begins. If a part isn't on the truck, we tell you what we're ordering and why.

Repair or replace? What the Air District rules mean for you

Under Bay Area Air District Rule 9-4, natural gas furnaces manufactured from 2029 onward must meet a zero-NOx emission standard. In practice, that will steer homeowners toward heat pumps when a furnace is replaced after that date.

The rule does not mean you have to replace a working furnace. It applies only when an existing furnace fails or is replaced, so repairing the equipment you have is still a reasonable choice. If your furnace is older and needs frequent repairs, though, it helps to know the rules before you decide how much more to put into it.

If you're thinking about a heat pump, be aware that the federal 25C tax credit covered qualifying heat pumps placed in service before December 31, 2025. It isn't available for new installations now. You may still find local options through BayREN and your clean energy provider. Those offers change with each funding cycle, so we confirm what's currently available before we include it in a quote.

Quick checks before you schedule

A few simple checks can sometimes save you a visit. If they don't solve the problem, they still help our technician find the cause faster.

If you smell gas, don't run the furnace or flip any switches. Leave the house and call your gas utility or 911 from outside.

  • Make sure the thermostat is set to Heat with the set point above room temperature, and replace its batteries if it uses them
  • Check the air filter and replace it if it's dirty
  • Confirm the furnace's power switch is on and the breaker hasn't tripped
  • Make sure the furnace door panel is fully closed, because many furnaces won't run when it's loose
  • Write down any error code or blinking light pattern

Serving Mountain View and nearby cities

We work in homes throughout Mountain View, including ZIP codes 94040, 94041 and 94043. Our technicians come from Santa Clara, about 6 miles away. We also serve nearby Los Altos, Sunnyvale, Palo Alto, Los Altos Hills and Cupertino.

Because Mountain View's winters are mild, many homeowners don't think about their furnace until it fails. A check in early fall, before the first cold week, can catch a dirty flame sensor, a clogged filter or a worn part while the problem is still small.

More services in Mountain View

Related

What to expect

How a visit goes

  1. We find the cause first

    Before we replace a part or suggest new equipment, we test the system and pin down what's actually wrong. You get an explanation of the problem, not just a fix.

  2. We lay out your options

    When there's more than one reasonable path, such as repairing an older furnace versus moving to a heat pump, we explain the trade-offs so you can decide what fits your home and plans.

  3. We check incentives before quoting them

    Heat pump and electrification incentives through BayREN and local clean energy providers change from one funding cycle to the next. We confirm what's currently offered before we mention it in a quote.

FAQ

Common questions

Don’t see your question? Call (669) 274-2169 and we’ll talk it through.

Do I have to replace my gas furnace because of the new Air District rules?

No. The Bay Area Air District rules don't require you to replace working equipment. They apply only when an existing furnace fails or is replaced. Gas furnaces manufactured from 2029 onward must meet a zero-NOx standard, which will point most replacements after that date toward heat pumps.

Is it worth repairing an older furnace?

Often it is, especially when the fix is a single part like an igniter or flame sensor. If the furnace needs repairs every season or the heat exchanger is damaged, we'll explain your options, including what the 2029 rule means for a future replacement.

Why does my furnace smell like burning when I first turn it on?

Dust settles on the burners and heat exchanger over the off-season and burns off when the heat comes on. That smell usually fades within a short time. If it lingers, smells electrical, or comes back every time the furnace runs, turn the furnace off and have it checked.

Why does my furnace shut off a few seconds after the burners light?

A common cause is a dirty flame sensor that can't confirm the flame, so the furnace shuts off the gas for safety. Restricted airflow, venting problems or a failing control board can cause similar symptoms. We test each one to find the actual cause.

Can I still get a federal tax credit for a heat pump?

Not for new installations. The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025. You can check BayREN and your local clean energy provider for current incentives, and we confirm any offer before including it in a quote.

Do you serve all of Mountain View?

Yes. We serve homes in ZIP codes 94040, 94041 and 94043, along with nearby Los Altos, Sunnyvale, Palo Alto, Los Altos Hills and Cupertino.

Tell us what your system is doing

Describe the problem, whether it's warm air from the vents, a furnace that won't start or a strange noise, and we'll schedule a technician to diagnose it and explain your options.

Call (669) 274-2169 Request Service